EATON-VICKERS液壓元件，DG4V-3-2A-M-P2-T-7-52
液壓管路將加壓流體從泵到馬達和回流從電動機
靈活或脊。個電源和個泵的尺寸可以提供個馬達或許多
臺泵和多臺電機可串聯或并聯連接（見各類型的連接
當泵連接到電機系列內部的過剩壓力的情況下是在創建
在每個電機壓力必須接回油箱。然而，使并聯連接時
電機沒有多余的情況下，壓力將增加。因此，使用殼體泄油口是沒有必要的。
查看應用程序，看看這個可選的殼體泄油口可以連接到你的，
馬達與泵連接，并聯連接到泵多臺電動機，以及多個電機
電機與有序殼體泄油口將隨安裝在年底鋼六角插頭
...泄油的 - 除了用于連接馬達提供較低的情況下的壓力
使增加了外部殼體泄油管的馬達具有正常的情況下，壓力為好。
包括：污染控制 - 沖洗馬達殼體。冷卻器系統 - 排出的油液使馬達
延長汽車密封件的壽命 - 通過安裝在預設的限制，低壓力的情況下
EATON-VICKERS液壓元件，DG4V-3-2A-M-P2-T-7-52
The hydrodynamic bearing has infinite life when shaft load
ratings are not exceeded. Hence, the shaft side load capacity
is more than adequate to handle most externally applied
loads (such as belts, chains, etc.), providing the motor to
shaft size is applied within its torque rating.
Allowable side load chart, shaft load location drawing and
load curves (below) are based on the side / radial loads
being applied to shaft at locations A, B, and C, to determine
the shaft side load capacity at locations other than those
shown use the formula (shown below). For more information
about shaft side loads on Char-Lynn motors contact
Use of Teflon Tape Sealant/Lubricant (with
1/2 14 NPTF Port Connectors only).
When using fittings with Teflon tape, be careful
when taping and tightening. Over tightening or
improperly taped fittings can cause damage
Use the following procedures:
?Wrap approx. 1 1/2 Turns of 13 mm [1/2 in.]
wide Teflon Tape around fitting threads ?start
tape 2 threads up from end of fitting.
?Tighten threads to a Maximum of 34 Nm [25
lb-ft]. ?Do Not Tighten Further ?
eak when tightened to maximum
torque, either retape, reseal, or replace fittings.